Husqvarna 2009 TE 250 Workshop Manual Download | Manualshive

Page: 263 / 412

background image

L.5

Part. N. 8000 H0368 (09-2008)

BRAKES

Wear check and replacement of brake pads

Inspect pads for wear.
Service limit “ A”

TE, TC, TXC

- 3,8 mm-0.15 in. (front and rear pads)
If service limit is exceeded, always replace the pads in pairs.

SMR

a) In front: thickness “A” must never be lower than the one pointed out by the wear
control notches.
b) At the back: thickness “A” must never be lower than 3,8 mm-0.15 in.
If service limit is exceeded, always replace the pads in pairs.
Be careful that no disc brake fluid or any oil gets on brake pads or discs. Clean off
any fluid or oil that inadverently gets on the pads or disc with alcohol.
Replace the pads with new ones if they cannot be cleaned satisfactorily.
PADS REMOVAL
-Remove springs (1).
-Remove pins (2).
-Remove pads.
PADS INSTALLATION
- Install new brake pads.
- Reassemble the two pins (2) and the springs (1).
If the above procedure is followed it will not be necessary to bleed the brake system
after new pads have been fitted.
Pumping the brake lever several times is sufficient to return the pistons to their
normal position.

During the operation of pads replacement, it is advisable to remove a small

quantity of fluid from reservoir, since piston backing inside cylinders could cause
overflowing of fluid from reservoir.

FRONT

REAR

2

1

1

2

FRONT

REAR

«
...
261
262
263
264
265
...
»

Summary of Contents for 2009 TE 250





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 TE 250

Brand: GIVI Pages: 3

Brand: hepco & becker Pages: 5

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 388

Brand: Yamaha Pages: 18

Brand: LAS Pages: 22

Brand: DYNATEK Pages: 8

Brand: hepco & becker Pages: 2

Brand: KTM Pages: 20

Brand: Chicago Electric Pages: 7

Brand: Chicago Electric Pages: 10

Brand: HYOSUNG Pages: 74

Brand: VOIGT MT Pages: 2

Brand: Benelli Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands