manualshive.com logo in svg

Husqvarna 2009 TE 250, Workshop Manual, Page: 19 / 412

Share
Download
Husqvarna 2009 TE 250 Workshop Manual Download Page 19

A.9

Part. N. 8000 H0368 (09-2008)

GENERAL

CAPACITIES

TYPE

QUANTITY

Fuel tank (reserve included)

Unleaded gasoline (98 R.O.N.)

1.58 Imp. Gall./ 1.9 U.S. Gall.

Fuel reserve

1.58 Imp. Qt./ 1.9 U.S. Qt.

Change gear and main transmission oil

AGIP RACING 4T (SAE 10W60)

1.5 Imp. Qt./ 1.8 U.S. Qt.
(oil and oil filter replacement)

Change gear and main transmission oil

AGIP RACING 4T (SAE 10W60)

1.3 Imp. Qt./ 1.6 U.S. Qt.
(oil replacement)

Front fork oil

AGIP FORK 7,5 (SAE 7,5; SAE for hard climatic conditions)

TC:

320 cm

3

TE:

725 cm

3

SMR:

740 cm

3

Oil for rear shock - absorber

AGIP FORK 2,5 (SAE 2,5)

Fluid for cooling system

AGIP COOL

2.0÷2.4 Imp. Pints; 2.3÷2.7 U.S. Pints

Front brake fluid

AGIP BRAKE 4 (DOT 4)

Rear brake fluid

AGIP BRAKE 4 (DOT 4)

Clutch fluid

OLIO MINERALE SAE 10 PER CIRCUITI IDRAULICI

Drive chain lubrication

AGIP CHAIN LUBE

Grease lubrication

AGIP BIKE GREASE

Electric contact protection

AGIP CONTACT CLEANER

Fillers for radiator

AREXONS TURAFALLE LIQUIDO

Air filter oil

AGIP FORMULA FILTER "Foam air filter protection oil"

Air filter detergent

AGIP "Filter clean foam air detergent fluid"

WARNING! - Use of additives in fuel or lubricants is not allowed

Summary of Contents for 2009 TE 250





























































































































































































































































































































































































































Reviews:

No comments