Huntleigh Sonicaid FM800 Series Instructions For Use Manual Download Page 13

 

Sonicaid FM800 Encore Series Instructions for Use 

 

13 

1.10

 

28B

Trademarks 

Sonicaid

 is a trademark of Huntleigh Healthcare Ltd. 

Safelinc

 is a trademark of Tyco. 

Qwik Connect

TM

 is a trademark of GE Medical 

Koala

®

 is a registered trademark of Clinical Innovations Inc. 

Nellcor is a trademark of Covidien AG 

1.11

 

29B

Sensors 

140B

Care and disposal 

Re-usable probes and sensors: store and maintain in accordance with the instructions 

supplied by the manufacturer. Probes and sensors which do not work, or which are no 

longer required, should be disposed of in accordance with local regulations. 

Single-use probes and sensors: dispose of these after use in accordance with local 

regulations. 

141B

Oximeter sensors 

The following types of sensor are approved for use with the FM830E: 

 

BCI (Smiths Industries) 3444 Finger Sensor 

 

NELLCOR DS100A 

The use of any other sensor may result in erroneous readings. 

1.12

 

30B

Residual Risks 

The residual risks are those risks that require a warning to 

be entered into this manual. They can be identified by the 

proximity of the following symbols. 

 

 

1.13

 

31B

Symbols 

 

Attention, consult accompanying documents/Instructions for Use 

 

This symbol signifies that this product, including its accessories and 

consumables is subject to the WEEE (Waste Electrical and Electronic 

Equipment) regulations and should be disposed of responsibly in accordance 

with local procedures. 

Summary of Contents for Sonicaid FM800 Series



































































































































Reviews: