Hunter Douglas Provenance Woven Wood Shades with PowerView Motorization Installation Operation And Care Download Page 4

Page: 4 / 28

GETTING STARTED

Thank you for purchasing Hunter Douglas Provenance

Woven Wood Shades with PowerView

™

Motorization. With proper installation, operation, and care, your new shades will provide years of
beauty and performance.

Please thoroughly review this instruction booklet and the enclosed packing list before beginning
the installation.

Tools and Fasteners Needed

■

Flat blade and Phillips screwdrivers

■

Measuring tape and pencil

■

Level (laser level is recommended)

■

Power drill,

" drill bit, and

" hex driver

In addition, you will need fasteners designed to work with your specific mounting surface(s).

■

#6 x 1

" Hex Head Screws (Provided).

Two 1

" screws are provided per installation

bracket.

■

Speed Nuts and Screws (Provided).

If ordered, extension brackets come with speed nuts

and screws.

■

Drywall Anchor (Not Provided).

Use drywall anchors when mounting into drywall.

■

#6 x 2" Hex Head Screws (Provided).

If using spacer blocks, two 2" screws are provided

per installation bracket.

Installation Overview

To install your shade, you will need to perform the following three steps:

STEP 1:

Install the Brackets

STEP 2:

Install the Shade

STEP 3:

Connect the Power Source

Speed Nut

and Screw

(Provided with Each

Optional Extension Bracket)

#6 x 1

Hex Head Screw

(Provided)

#6 x 2" Hex Head Screw

Provided with Each

Spacer Block

Summary of Contents for Provenance Woven Wood Shades with PowerView Motorization





























Search results

Summary of Contents for Provenance Woven Wood Shades with PowerView Motorization

Reviews:

Related manuals for Provenance Woven Wood Shades with PowerView Motorization

Brands by name

Popular brands

Hunter Douglas Provenance Woven Wood Shades with PowerView Motorization, Installation Operation And Care

Search results

Summary of Contents for Provenance Woven Wood Shades with PowerView Motorization

Reviews:

Related manuals for Provenance Woven Wood Shades with PowerView Motorization

Brands by name

Popular brands