Hunter Douglas Provenance Woven Wood Shades with PowerView Motorization Installation Operation And Care Download Page 13 | Manualshive

Page: 13 / 28

background image

INSTALLATION

11

If You Have a Satellite Battery Pack...

Install Batteries into the Battery Wand

■

See the instructions on the previous page.

Mount the Satellite Battery Pack

■

Decide where you want to attach the wall mount bracket.
A satellite battery pack may be mounted in any orientation.

■

Mark the screw holes.

■

Drill the screw holes using a

3

/

32

" drill bit.

■

Remove the backing from the double-sided tape. Press the bracket into place.

■

Attach the bracket using the screws provided.

■

Position the battery wand so the power cable is easily connected to the socket.

■

Snap the battery wand into the bracket.

■

Install the battery wand cover with the slot aligned to the socket in the battery wand.

Wall Mount Bracket

Socket

Battery Wand Cover

Slot

Socket

«
...
11
12
13
14
15
...
»

Summary of Contents for Provenance Woven Wood Shades with PowerView Motorization





























Reviews:

No comments

Related manuals for Provenance Woven Wood Shades with PowerView Motorization

Brand: paladin Pages: 3

Brand: WA Library Supplies Pages: 2

Brand: Kanto Pages: 8

Brand: baby&child Pages: 3

Brand: Wayfair Pages: 3

Brand: Gautier Pages: 40

Brand: HAMPTON BAY Pages: 16

PRATO 147163BEIG

Brand: CAFOM SOURCING Pages: 4

Westwood Modula Wall Unit

Brand: JD Williams Pages: 16

Brand: Coaster Pages: 7

Brand: Pro-Lift Pages: 3

Basculante PA623P

Brand: BENITO Pages: 2

Brand: De La Espada Pages: 7

Ellsworth 06-074

Brand: RiverRidge Pages: 20

Brand: HAMPTON BAY Pages: 8

PULLBOY VARIO 30er

Brand: Wesco Pages: 2

Brand: Hooker Furniture Pages: 3

Brand: KLOBER Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands