Hughes HX90 User Manual Download Page 44

Page: 44 / 88

Chapter 4 • Troubleshooting

1039457-0001 Revision A

The System Information page appears.

Figure 27: System Info page

Note:

The System Info page for your installation may show different fields and

values.

2. In the

HX90

section, check the

Site ID

line.

If the numeric site ID appears, the satellite router is commissioned. Proceed to

Confirming the receive signal

on page 44.

Not_Commissioned

appears, the router is not commissioned. Contact your

service provider.

Confirming the receive signal

To confirm that the router is properly receiving satellite signals:

1. At the System Control Center, click the

Reception Info

link.

The Reception Information page appears.

2. In the

Receive Status

field, check the RxCode.

If the RxCode is

Receiver operational (RxCode 5)

the router is receiving signals

properly; proceed to

Confirming the transmit signal

on page 45.

Summary of Contents for HX90

























































































Search results

Summary of Contents for HX90

Reviews:

Related manuals for HX90

Brands by name

Popular brands

Hughes HX90, User Manual

Search results

Summary of Contents for HX90

Reviews:

Related manuals for HX90

Brands by name

Popular brands