Hughes HN9400 Installation Manual Download

Page: 3 / 134

Contents

Understanding safety alert messages.................................................................................xi

Messages concerning personal injury.....................................................................................................xi

Messages concerning property damage...................................................................................................xi

Safety symbols........................................................................................................................................xi

Chapter 1: Satellite router overview..............................................................1

Scope of this installation guide................................................................................................................2

Satellite router specifications...................................................................................................................2

LAN port configuration............................................................................................................................2

Chapter 2: Preparing for installation.............................................................5

Installation summary................................................................................................................................6

Installation checklist.................................................................................................................................7

Items required for installation..................................................................................................................8

Conducting a site survey..........................................................................................................................9

Power supply information........................................................................................................................9

Computer and networking requirements................................................................................................10

Computer requirements..............................................................................................................10

Networking and Internet browser requirements.........................................................................11

Related components...............................................................................................................................11

Antenna......................................................................................................................................11

IFL cables...................................................................................................................................12

Requirements for cables, connectors, and ground blocks..............................................12

Labeling the IFL cables..................................................................................................12

Hub or similar network device...................................................................................................12

Instructions for related components...........................................................................................12

Chapter 3: Installing the satellite router......................................................15

Prerequisites for installing the router.....................................................................................................16

Selecting the router installation location................................................................................................16

Ventilation and heat sources.......................................................................................................16

Router operating position.......................................................................................................................16

Connecting the transmit and receive cables...........................................................................................17

Connecting the installer laptop to the router..........................................................................................18

Connecting the power supply.................................................................................................................19

Connecting an AC/DC power supply.........................................................................................19

Connecting and assembling a DC/DC power supply.................................................................20

Powering up the router...........................................................................................................................21

AC/DC power supply.................................................................................................................21

iii

HN9400 Satellite Router Installation Guide

1038554-0001 Revision B

Summary of Contents for HN9400







































































































































Search results

Summary of Contents for HN9400

Reviews:

Related manuals for HN9400

Brands by name

Popular brands

Hughes HN9400, Installation Manual

Search results

Summary of Contents for HN9400

Reviews:

Related manuals for HN9400

Brands by name

Popular brands