Hughes HN9400 Installation Manual Download Page 37

Page: 37 / 134

Verifying the Ethernet connection

Execute a ping test to verify that the Ethernet connection between the satellite router and the
installer laptop is active:

Open a command prompt or window on the installer laptop.

Type

ping 192.168.0.1

Press

Enter

If the ping is successful, the ping results show that all sent packets were received.

Figure 9: Successful ping test

If the ping fails, the ping results show that packets were lost, and time-out messages may
also appear.

Figure 10: Failed ping test

If the ping test fails, make sure:

•

The laptop’s network interface card (NIC) is properly installed

•

The laptop is configured to support DHCP

If the NIC is installed properly and the laptop is configured to support DHCP, make sure all
cable connections are secure (properly aligned—not cross threaded; finger tight with no
play).

If the connections are secure:

a) Unplug the router from the power source.
b) Shut down and power off the computer.
c) Plug the router back in.
d) Turn the computer back on.

HN9400 Satellite Router Installation Guide

1038554-0001 Revision B

Chapter 4

Commissioning the satellite router

Summary of Contents for HN9400







































































































































Search results

Summary of Contents for HN9400

Reviews:

Related manuals for HN9400

Brands by name

Popular brands

Hughes HN9400, Installation Manual

Search results

Summary of Contents for HN9400

Reviews:

Related manuals for HN9400

Brands by name

Popular brands