Hughes HN9400 Installation Manual Download Page 44

Page: 44 / 134

Figure 18: Satellite Parameters screen

From the list, select the satellite transponder listed on the Installation Reference Sheet or
installation specification; then click

Next

Note:

If your satellite transponder is not listed in the drop-down list, you must use the

manual entry method. See

Entering the antenna location (manual entry)

on page 30.

Note:

The list of satellite transponders may be updated at any time, so you may see

different transponders than those shown in

Figure 18: Satellite Parameters screen

page 32.

The Verification of Satellite Parameters screen appears.

HN9400 Satellite Router Installation Guide

1038554-0001 Revision B

Commissioning the satellite router

Chapter 4

Summary of Contents for HN9400







































































































































Search results

Summary of Contents for HN9400

Reviews:

Related manuals for HN9400

Brands by name

Popular brands

Hughes HN9400, Installation Manual

Search results

Summary of Contents for HN9400

Reviews:

Related manuals for HN9400

Brands by name

Popular brands