Hughes HN9400 Installation Manual Download | Manualshive

Page: 18 / 134

background image

Installation summary

This guide explains how to install the HN9400 satellite router. It includes

limited

information

about other satellite terminal components. The

satellite router

is the small indoor unit. The

satellite terminal

includes the satellite router and the antenna, radio assembly, and IFL cables,

as shown in

Figure 2: Satellite router and related terminal components

on page 6.

Figure 2: Satellite router and related terminal components

This summary focuses on installation of the satellite router, but also includes some information
on related tasks such as antenna installation and pointing. The tasks listed below are the main
installation tasks,

but these are not all

of the installation tasks.

Complete all steps in the order they are presented in this installation guide unless you have a
specific reason for doing them in a different order. In any case, make sure all steps are completed.
You must install the antenna before the satellite router can be commissioned. Then you point
the antenna as part of the router commissioning procedure.

Details for the satellite router installation tasks are included in later chapters in this guide.

Preparing for the installation

• Make sure you have all items required for installation, including the Installation Reference

Sheet and installation specification, all equipment to be installed, and required tools for the
outdoor equipment.

•

Consumer installations only:

Make sure the customer's computer meets the requirements

listed in

Computer and networking requirements

on page 10.

• Conduct a site survey.
• Assemble and install the antenna and radio as instructed in the antenna installation guide.

Installing the satellite router

• Connect the transmit and receive cables.
• Connect the router to the installer laptop.
• Connect the power supply.
• Power up the router and observe the LEDs to verify normal operation.

Commissioning the router and pointing the antenna

HN9400 Satellite Router Installation Guide

6

1038554-0001 Revision B

Preparing for installation

Chapter 2

«
...
16
17
18
19
20
...
»

Summary of Contents for HN9400







































































































































Reviews:

No comments

Related manuals for HN9400

Brand: XAVI Technologies Corp. Pages: 59

Brand: StarHub Pages: 10

Brand: Elastic Networks Pages: 32

Brand: Ebyte Pages: 39

Brand: Four-Faith Pages: 34

Brand: Raymar Pages: 19

Brand: Hughes Network Systems Pages: 154

Brand: M-Life Pages: 52

Brand: O2 Pages: 56

Barricade SMC7904BRB2

Brand: SMC Networks Pages: 2

7901BRA - FICHE TECHNIQUE

Brand: SMC Networks Pages: 2

Brand: DOUXE Pages: 9

Brand: Zte Pages: 7

Brand: Accedian Pages: 206

Brand: Dataradio Pages: 24

Brand: Dataradio Pages: 69

Brand: TeamOne Pages: 64

Brand: NETGEAR Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands