Hughes HN9400 Installation Manual Download

Page: 32 / 134

Figure 7: Connecting an AC power supply

Connecting and assembling a DC/DC power supply

Figure 8: DC/DC power supply

on page 20 shows the DC/DC power supply used with the

HN9400 router.

Figure 8: DC/DC power supply

Connect and assemble the DC/DC power supply as follows:

Connect the DC power cord to the DC IN port on the router.

Note:

The input cable kit is included in the power supply kit. The cable kit contains

an input power connector, connector pins, and a wiring diagram; it does not include
wire.

Assemble the input power cable according to the wiring diagram included in the cable kit.

HN9400 Satellite Router Installation Guide

1038554-0001 Revision B

Installing the satellite router

Chapter 3

Summary of Contents for HN9400







































































































































Search results

Summary of Contents for HN9400

Reviews:

Related manuals for HN9400

Brands by name

Popular brands

Hughes HN9400, Installation Manual

Search results

Summary of Contents for HN9400

Reviews:

Related manuals for HN9400

Brands by name

Popular brands