background image

2). Press "Settings" key to enter setting interface

3). In "Function", select "P"(Path)

Press "↓" or "↑" key to make the gray cursor on "Function" menu bar. After

pressing "→" or "←" key between "L"(Location) "P"(path), select "P"(i.e. select the

path mode). After selecting the function, press "Start-Stop" key to exit the setting

screen and enter the sampling display interface.

The path mode is a combination with a path signal generator provided by the

manufacturer to work. Connect the line correctly between the signal generator and the

fault cable, and plug the power supply of path signal generator, then select the signal

frequency, and adjust the output power of the generator(i.e., the output current of

signal generator), and make sure that the output current value is greater than 50 mA

and less than 100 mA. Under normal circumstances, you can hear "beep" sound from

signal generator in the headphones of the location instrument.

Press "↓" or "↑" key to adjust the size of the sound heard, and press "→" or "←"

key to adjust the amount of amplification of electromagnetic receiver. Usually the

electromagnetic gain is adjusted to 20% - 60%, and voice gain adjustment for 50% -

80%. You can make an appropriate adjustment according to the specific circumstances

of the site.

After moving the probe matching with the location instrument, measure the

underground route of cable with maximum or minimum method according to "path

measurement principle"of the fifth behind.

While listening to the sound, LCD will display waveform of sound signal

emitted by the current path of signal generator after detector and prompt waveform

amplitude. according to the size of sound heard and magnitude of waveform observed,

it can be a reference instruction for underground route of cable.

Summary of Contents for HZ-4000T2


































































Reviews: