Huawei UPS5000-S-1200 kVA User Manual Download Page 126

Page: 126 / 215

UPS5000-S-1200 kVA
User Manual

4 User Interface

Issue 04 (2019-06-25)

118

Item

Description

Default Value Value Range

(C10)

Cell float
voltage (V/cell)

Specifies the battery float
charging voltage.

2.25 V/cell

2.23 V/cell to
2.30 V/cell

Cell equalized
volt. (V/cell)

Specifies the battery equalized
charging voltage.

2.35 V/cell

2.30 V/cell to
2.40 V/cell

Dis. cur. 0.1C
EOD (V/cell)

Specifies the EOD threshold
when the discharging current is
0.1C, 0.3C, 0.5C, and 1.0C
respectively.

1.80 V/cell

1.8–1.9

Dis. cur. 0.3C
EOD (V/cell)

1.80 V/cell

1.8–1.9

Dis. cur. 0.5C
EOD (V/cell)

1.75 V/cell

1.75–1.85

Dis. cur. 1.0C
EOD (V/cell)

1.60 V/cell

1.6–1.75

Sched. shallow
dis. test

When certain conditions are met,
the charger shuts down, and
batteries supply power to loads.
The system records the battery
discharge data as the reference
for battery capacity and lifespan.

Disable

Disable, Enable

Shallow dis.
test dis. ratio
(%)

Set the proportion of the
discharge capacity to the total
discharge capacity. The value is
configurable in any mode.

20%

10%–50%

iBOX Settings

Figure 4-31

iBOX settings

Summary of Contents for UPS5000-S-1200 kVA
























































































































































































































Search results

Summary of Contents for UPS5000-S-1200 kVA

Reviews:

Related manuals for UPS5000-S-1200 kVA

Brands by name

Popular brands

Huawei UPS5000-S-1200 kVA, User Manual

Search results

Summary of Contents for UPS5000-S-1200 kVA

Reviews:

Related manuals for UPS5000-S-1200 kVA

Brands by name

Popular brands