manualshive.com logo in svg

Huawei UPS5000-S-1200 kVA, User Manual

The Huawei UPS5000-S-1200 kVA is a reliable and efficient power supply solution. Its user-friendly design ensures easy operation and maintenance. To learn more about its features and functionalities, download the free User Manual from manualshive.com to enhance your understanding and optimize performance.

Share
Download
background image

UPS5000-S-1200 kVA 
User Manual 

10 Alarm List 

 

Issue 04 (2019-06-25) 

Copyright © Huawei Technologies Co., Ltd. 

196 

 

Alarm ID 
(Alarm 
ID-Cause 
ID) 

Alarm Name  Severity 

Cause 

Solution 

incorrect. 

2.

 

Check that the neutral wire to the power 
distribution system is normal. 

0006-1 

Mains 
undervoltage 

Minor 

 

The mains is 
not normal. 

 

The power 
module 
sampling 
circuit is not 
normal. 

Check whether the mains voltage ranges 
from 80 V (excluding 80 V) to 176 V. If no, 
the mains monitoring circuit for the power 
module is faulty. Replace the faulty 
module. 

0010-1 

Abnormal 
bypass voltage 

Minor 

 

The bypass 
voltage range 
is not 
correctly set. 

 

The bypass 
input voltage 
is not normal. 

1.

 

Check the bypass input voltage or cable 
connections with a multimeter. 

2.

 

Check the voltage system and bypass 
voltage thresholds configured on the 
LCD. 

0010-2 

 

The bypass 
frequency 
range is not 
correctly set. 

 

The bypass 
input 
frequency is 
not normal. 

1.

 

Check the bypass input voltage or cable 
connections with a multimeter. 

2.

 

Check the bypass input frequency. 
Check the rated frequency and 
frequency range configured on the LCD. 

0011-1 

Bypass phase 
reversed 

Minor 

The phase 
sequence of the 
three-phase 
bypass input is 
reversed. 

Check whether the cable phase sequence is 
correct using a multimeter. If no multimeter 
is available, exchange the positions of any 
two cables. 

0012-1 

Bypass neutral 
absent 

Minor 

The neutral wire 
of bypass input 
is not installed 
properly. 

1.

 

Secure or connect the neutral wire to the 
cabinet if it is loose or disconnected. 

2.

 

Check that the neutral wire to the power 
distribution system is normal. 

0020-1 

Battery 
connected 
reversely 

Critical 

Batteries are not 
properly 
installed. 

1.

 

Check whether battery polarities are 
correctly installed by using a 
multimeter. If no, correct the 
installation. 

2.

 

Check whether the battery input voltage 
of the UPS is normal. If yes, the battery 
sampling circuit of the power module is 
faulty. Replace the power module. 

0021-1 

Battery EOD 

Critical 

The battery 
voltage reaches 
the EOD voltage 

If the BCB box is configured, check 
whether the BCB box trips. If it trips, close 
the BCB box switch. 

Summary of Contents for UPS5000-S-1200 kVA
























































































































































































































Reviews:

No comments

Related manuals for UPS5000-S-1200 kVA

Bartscher 700 Series Instructions For Installation, Use And Maintenance Manual preview
700 Series
Brand: Bartscher Pages: 22
Laica SB2200 Instructions And Guarantee preview
SB2200
Brand: Laica Pages: 4
Harken T2 Instructions preview
T2
Brand: Harken Pages: 4
MacDon R216 Quick Card preview
R216
Brand: MacDon Pages: 2
MacDon R216 Operator'S Manual preview
R216
Brand: MacDon Pages: 214
MacDon R216 Installation Instructions Manual preview
R216
Brand: MacDon Pages: 32
Cadman 6010 Operator And Maintenance Manual preview
6010
Brand: Cadman Pages: 66
Raytech TR-1 Instruction Manual preview
TR-1
Brand: Raytech Pages: 21
Teac LX Series Specifications preview
LX Series
Brand: Teac Pages: 2
laerdal HEARTSTART Quick Start Manual preview
HEARTSTART
Brand: laerdal Pages: 2
Kamikaze KV 4 User Manual preview
KV 4
Brand: Kamikaze Pages: 112
KAM LED PAR 56 Product Manual preview
LED PAR 56
Brand: KAM Pages: 2
KaVo Scan eXam One Quick Manual preview
Scan eXam One
Brand: KaVo Pages: 4
KaVo ORTHOPANTOMOGRAPH OP 3D Installation Manual preview
ORTHOPANTOMOGRAPH OP 3D
Brand: KaVo Pages: 40
KaVo KEY Laser III 1243 Instructions For Use Manual preview
KEY Laser III 1243
Brand: KaVo Pages: 103
KaVo EXTRAmatic 9040 Instructions For Use Manual preview
EXTRAmatic 9040
Brand: KaVo Pages: 56
KaVo ESTETICA E70 Vision Care Instructions preview
ESTETICA E70 Vision
Brand: KaVo Pages: 48
Kaya Safety F-6 User Manual preview
F-6
Brand: Kaya Safety Pages: 5

Brands by name

Popular brands

Load more brands