manualshive.com logo in svg

Huawei UPS5000-S-1200 kVA, User Manual

The Huawei UPS5000-S-1200 kVA is a reliable and efficient power supply solution. Its user-friendly design ensures easy operation and maintenance. To learn more about its features and functionalities, download the free User Manual from manualshive.com to enhance your understanding and optimize performance.

Share
Download
background image

UPS5000-S-1200 kVA 
User Manual 

2 Overview 

 

Issue 04 (2019-06-25) 

Copyright © Huawei Technologies Co., Ltd. 

25 

 

Silk Screen 

Description 

PARALLEL 

The PARALLEL port transmits parallel signals between 
racks. 

BSC 

The BSC port is used in a dual-bus system to synchronize 
output frequencies and phases between UPS systems, 
ensuring that two buses can switch with each other. 

BSC cables are hot-swappable. 

 

Table 2-5

 

Indicator description 

Indicator 

Color 

Status 

Description 

NORMAL 

Green 

Steady on 

This ECM is the active ECM. 

Blinking at 0.5 
Hz 

This ECM is the standby ECM and it is 
ready. 

Off 

This ECM is not ready or the CPLD of 
this ECM is being upgraded. 

Blinking at 4 Hz 

The DSP of the ECM is being upgraded or 
not configured. 

ALM 

Yellow 

Steady on 

The ECM has a minor alarm, but it does 
not need to be replaced. 

Off 

The ECM has no minor alarm or the DSP 
of the ECM is being upgraded. 

FAULT 

Red 

Steady on 

The ECM has a critical alarm. 

Off 

The ECM has no critical alarm or the DSP 
of the ECM is being upgraded. 

 

Functions 

 

As a control interface for the entire system, the ECM communicates with each module 
and provides a bus to communicate with the dry contact card. The ECM ensures 
equalized output currents between modules so that load power is equally shared. 

 

Provides module running information for the MDU. 

 

Controls the running of a single UPS5000, and reports the UPS5000 status information 
to other monitoring modules. 

 

The system provides three types of CAN communication: monitoring CAN 
communication, intra-rack parallel CAN communication, and inter-rack parallel CAN 
communication. 

Specifications 

 

Hot-swappable 

 

1 U high 

Summary of Contents for UPS5000-S-1200 kVA
























































































































































































































Reviews:

No comments

Related manuals for UPS5000-S-1200 kVA

Calistair C300 Translation Of The Original Operating Instructions preview
C300
Brand: Calistair Pages: 44
MachMotion 2000 Series Operating Manual preview
2000 Series
Brand: MachMotion Pages: 33
Falcon 90 Instructions For Use And Installation preview
90
Brand: Falcon Pages: 52
parr 1108 Operating Instructions Manual preview
1108
Brand: parr Pages: 20
Landoll 2110 Operator'S Manual preview
2110
Brand: Landoll Pages: 71
York Fitness 2110 Owner'S Manual preview
2110
Brand: York Fitness Pages: 4
W&H 206 Operator'S Manual preview
206
Brand: W&H Pages: 23
Bartscher 105 Original Instruction Manual preview
105
Brand: Bartscher Pages: 24
Abbott CentriMag Quick Reference Manual preview
CentriMag
Brand: Abbott Pages: 2
Abbott FreeStyle Libre Software Update preview
FreeStyle Libre
Brand: Abbott Pages: 3
abc PHASER Operation And Maintenance Manual preview
PHASER
Brand: abc Pages: 8
SAMCHULLY HCH Instruction Manual preview
HCH
Brand: SAMCHULLY Pages: 48
HAGER WERKEN SPEEDO-CLEAN Instructions For Use preview
SPEEDO-CLEAN
Brand: HAGER WERKEN Pages: 2
MAHA MBT Series Operating Instructions Manual preview
MBT Series
Brand: MAHA Pages: 21
MAGUIRE PRS-20 Installation Operation & Maintenance preview
PRS-20
Brand: MAGUIRE Pages: 47
EFX EFF523 Instructions For Use preview
EFF523
Brand: EFX Pages: 2
Yacht Devices YDEG-04 User Manual preview
YDEG-04
Brand: Yacht Devices Pages: 68
Rigol RP1010H User Manual preview
RP1010H
Brand: Rigol Pages: 12

Brands by name

Popular brands

Load more brands