Huawei UPS5000-S-1200 kVA User Manual Download Page 120

Page: 120 / 215

UPS5000-S-1200 kVA
User Manual

4 User Interface

Issue 04 (2019-06-25)

112

Item

Description

Default Value Value Range

overdischarge.

Intra-rack power

module start delay (s)

can be set

to a value ranging from 0.5 to
120.

Inter-rack power module

start delay (s)

can be set to a

value ranging from 2 to 120. The
preset value of

Inter-rack power

module start delay (s)

is 5.0.

The start delay of a module in a
rack varies depending on the rack
number and module number. #1
module in rack 1 does not have a
start delay.

Maintenance
bypass cabinet

If the maintenance bypass unit is
configured, set this parameter to

Enable

Disable

Disable, Enable

Intelligent
detection
module

N/A

Disable

Disable, Enable

Input Settings

Figure 4-25

Input settings

Item

Description

Default Value Value Range

D.G. mode

Set this parameter to

Enable

when a D.G. connects to the
input PDC. The UPS enters the
D.G. mode when a D.G. is
detected over dry contacts.

Disable

Disable, Enable

D.G. power
limiting (kVA)

Set these two parameters to
control the valid input current

800 kVA

0 kVA to 5000
kVA

Summary of Contents for UPS5000-S-1200 kVA
























































































































































































































Search results

Summary of Contents for UPS5000-S-1200 kVA

Reviews:

Related manuals for UPS5000-S-1200 kVA

Brands by name

Popular brands

Huawei UPS5000-S-1200 kVA, User Manual

Search results

Summary of Contents for UPS5000-S-1200 kVA

Reviews:

Related manuals for UPS5000-S-1200 kVA

Brands by name

Popular brands