Huawei UPS5000-S-1200 kVA User Manual Download Page 86

Page: 86 / 215

UPS5000-S-1200 kVA
User Manual

3 Installation

Issue 04 (2019-06-25)

Figure 3-56

Securing the cabinet

When installing the anchor screws at the rear of the fan, remove the bottom cover, tighten the anchor
screws, and reinstall the cover.

----End

Installing a Busbar

The procedure for installing the sealing plate is different. For details about other steps, see the
procedure for installing the busbar.

Step 1

Install the right sealing plate of the input/output unit.

Figure 3-57

Install the right sealing plate

Step 2

Remove the rear sealing plate from the power unit.

Summary of Contents for UPS5000-S-1200 kVA
























































































































































































































Search results

Summary of Contents for UPS5000-S-1200 kVA

Reviews:

Related manuals for UPS5000-S-1200 kVA

Brands by name

Popular brands

Huawei UPS5000-S-1200 kVA, User Manual

Search results

Summary of Contents for UPS5000-S-1200 kVA

Reviews:

Related manuals for UPS5000-S-1200 kVA

Brands by name

Popular brands