Huawei TP3206 Installation Manual Download Page 33

Page: 33 / 200

HUAWEI TP3206&TP3218&TP3218S Telepresence

Installation Guide

5 Installing the Rack

Issue 05 (2014-08-01)

Huawei Proprietary and Confidential

No.

Name

Quantity

T-shaped front panel support (A17)

M6 x 16 socket-head cap screw

Several

M6 x 30 socket-head cap screw

Several

Cable label

Several

5.2 Installation Procedure

Follow the procedure in this section to install the racks.

5.2.1 Connecting Racks

Do not shake the racks. Otherwise, the racks may fall and cause personnel injury or device

damage.

The left, center, and right racks are labeled "Left", "Middle", and "Right" respectively. During

installation, locate the racks from left to right, with the labels against the rear wall.

Procedure

Step 1

Place the seven rear panels against the rear wall, with the arrows on the attached labels

pointing upward.

Step 2

Determine the location of the center rack (A1).which is 10 cm away from the rear wall, as

shown in

Figure 5-1

主机架距离两侧墙面的位置请参见

Huawei TP3206 Telepresence

Room Decoration Guide

Huawei TP3218 Telepresence Room Decoration Guide

, and

Huawei

TP3218S Telepresence Room Decoration Guide

Figure 5-1

Location of the center rack

Step 3

Partially tighten the screws in the bottom connecting plates (A4) to connect the three racks.

The connecting method is the same for the left and right racks. The following procedure uses

the left rack as an example. See

Figure 5-2

Summary of Contents for TP3206









































































































































































































Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands

Huawei TP3206, Installation Manual

Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands