Huawei Telecom Power TBC300A-DCA5 User Manual Download Page 89 | Manualshive

Page: 89 / 95

background image

TP48200A-HX09A1 and TBC300A-DCA5 Telecom
Power
User Manual

A Technical Specifications

Issue 03 (2019-11-15)

Copyright © Huawei Technologies Co., Ltd.

82

Item

Specifications

interference (EMI)

Radiated emission (RE)

Class A, EN300386

Harmonic

IEC 61000-3-12

Fluctuation and flick

IEC 61000-3-11

Electromagnetic
susceptibility (EMS)

Electrostatic discharge (ESD)

Contact discharge: 6 kV (criterion B); air discharge:
8 kV (criterion B)

Electrical fast transient (EFT)

EN61000-4-4

Signal port: ±1 kV (criterion B); AC power port: ±2
kV (criterion B); DC power port: 2 kV (criterion B)

Radiated susceptibility (RS)

Field strength: 10 V/m (criterion A)

Conducted susceptibility (CS)

Signal port: 3 V (criterion A); power port: 10 V
(criterion A)

Surge susceptibility

EN61000-4-5

AC and DC power ports: differential mode: ±2 kV
(criterion B); common mode: ±4 kV (criterion B).
Signal port: differential mode: 0.5 kV (criterion B);
common mode: 1 kV (criterion B)

A.4 Cabinet Specifications

Table A-4

Cabinet specifications

Function

Specifications

Dimensions (H x W x D)

900 mm x 650 mm x 650 mm (excluding the base and protruding part)

Base (H x W x D)

100 mm x 650 mm x 650 mm

Cabinet weight

TP48200A-HX09A1: ≤ 75 kg (without rectifiers)

TBC300A-DCA5: ≤ 50 kg (without batteries)

Protection level

TP48200A-HX09A1: IP55

TBC300A-DCA5: IP34

Installation mode

TP48200A-HX09A1: installed on a floor, installed against a wall,
combined with a battery cabinet, or stacked on a battery cabinet

TBC300A-DCA5: installed on a floor, installed against a wall (with a
clearance of greater than 100 mm), combined with a power cabinet or
battery cabinet, stacked under a power cabinet, or stacked on or under a
battery cabinet

Maintenance mode

Operated and maintained from the front

Cable routing

Routed in and out from the bottom

«
...
87
88
89
90
91
...
»

Summary of Contents for Telecom Power TBC300A-DCA5
































































































Reviews:

No comments

Related manuals for Telecom Power TBC300A-DCA5

Brand: Watchguard Pages: 40

DES-3526 - Switch - Stackable

Brand: D-Link Pages: 258

Brand: Paradyne Pages: 20

Compshere 3000 Series

Brand: Paradyne Pages: 2

Brand: Pantech Pages: 17

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Brand: D-Link Pages: 53

Brand: STONEFLY Pages: 48

Brand: Direct IP Pages: 76

eXtremeRAID 1100

Brand: Mylex Pages: 74

Brand: Ruckus Wireless Pages: 56

Brand: Renesas Pages: 6

Brand: WHOOP Pages: 26

DG834GT - 108 Mbps Super G Wireless ADSL Router

Brand: NETGEAR Pages: 2

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: Abocom Pages: 1

Brand: Justec Pages: 61

CNPS7000A Series

Brand: ZALMAN Pages: 9

EK-FC285 GTX Classified

Brand: ekwb Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands