Huawei Telecom Power TBC300A-DCA5 User Manual Download Page 70

Page: 70 / 95

TP48200A-HX09A1 and TBC300A-DCA5 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Figure 4-15

Removing the external fan

Step 6

Place the new fan based on the recorded installation direction (see the arrow marks on the fan),
and screw the fan to the fan fixing plate.

Step 7

Properly place the fan fixing plate and screw up the fan fixing plate.

Step 8

Properly place the fan baffle and screw up the fan baffle.

Step 9

Connect the wiring terminal for the fan.

Step 10

Connect the –48V power cable to the UIM02C.

Step 11

Push in the UIM02C and secure the screws.

Step 12

Connect the signal cable to the UIM02C panel based on the record made previously.

Step 13

Disconnect the ground cable from the ESD wrist strap and take off the ESD wrist strap and
ESD gloves.

----End

4.4.8 Replacing the Heat Exchanger Core

Prerequisites

Protect yourself against being burnt when removing the heat exchanging core as it has a high
temperature.

You have obtained an ESD wrist strap, a pair of ESD gloves, a pair of protective gloves, the
cabinet door key and maintenance tool box.

Context

You do not need to disconnect the AC input for the system.

Summary of Contents for Telecom Power TBC300A-DCA5
































































































Search results

Summary of Contents for Telecom Power TBC300A-DCA5

Reviews:

Related manuals for Telecom Power TBC300A-DCA5

Brands by name

Popular brands

Huawei Telecom Power TBC300A-DCA5, User Manual

Search results

Summary of Contents for Telecom Power TBC300A-DCA5

Reviews:

Related manuals for Telecom Power TBC300A-DCA5

Brands by name

Popular brands