Huawei Telecom Power TBC300A-DCA5 User Manual Download Page 93

Page: 93 / 95

TP48200A-HX09A1 and TBC300A-DCA5 Telecom
Power
User Manual

C Associations between Alarms and Dry Contacts on the

UIM

Issue 03 (2019-11-15)

Port Type

Silk Screen

Associated Alarm

Default mode (Close: alarm; Open: normal) can be modified
as required.

ALM7

Reports alarms for door status (including the power cabinet
and battery cabinet).

Default mode (Close: alarm; Open: normal) can be modified
as required.

ALM8

Reports alarms for battery cabinet heater faults, fan faults
(including the power cabinet and battery cabinet), and high
temperatures detected by the temperature control unit (TCU)
in the power cabinet.

Default mode (Close: alarm; Open: normal) can be modified
as required.

Summary of Contents for Telecom Power TBC300A-DCA5
































































































Search results

Summary of Contents for Telecom Power TBC300A-DCA5

Reviews:

Related manuals for Telecom Power TBC300A-DCA5

Brands by name

Popular brands

Huawei Telecom Power TBC300A-DCA5, User Manual

Search results

Summary of Contents for Telecom Power TBC300A-DCA5

Reviews:

Related manuals for Telecom Power TBC300A-DCA5

Brands by name

Popular brands