Huawei Telecom Power TBC300A-DCA5 User Manual Download Page 48

Page: 48 / 95

TP48200A-HX09A1 and TBC300A-DCA5 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Maintenance

4.1 Routine Maintenance

Routine maintenance is required periodically based on the site requirements. The
recommended maintenance interval is six months. If any faults occur, rectify the faults in
time.

Table 4-1

Routine maintenance checklist

Maintenance
Item

Check Whether

Check Method

Repair When

Measures

Cabinet door lock

The door lock is
damaged.

By observing, or by
locking and
unlocking the door.

The door lock fails.

Replace the door
lock.

Fan

Dust accumulates
on the fan surface.

By observing.

Thick dust
accumulates on the
fan surface.

Clean up the dust
from the fan.

The fan surface is
intact and the
rotational speed,
noise, and vibration
are in the normal
range.

By observing and
listening to the fans.

The fan is damaged,
the noise is too
loud, or the
vibration is
abnormal.

Replace the fan.

Heat exchanger

Dust accumulates
on the surface of
the heat exchanging
core.

By observing or
checking the
temperature.

Thick dust
accumulates on the
surface of the heat
exchanging core,
and the temperature
inside the cabinet is
overhigh.

Clean or replace the
heat exchanging
core.

Heater

The heater works
normally.

By observing or
checking the
temperature.

The heater is
damaged and
cannot effectively
heat the air.

Replace the heater.

TCUA control

The TCUA control
board works

By observing, and
checking the

The TCUA control
board works

Replace the TCUA

Summary of Contents for Telecom Power TBC300A-DCA5
































































































Search results

Summary of Contents for Telecom Power TBC300A-DCA5

Reviews:

Related manuals for Telecom Power TBC300A-DCA5

Brands by name

Popular brands

Huawei Telecom Power TBC300A-DCA5, User Manual

Search results

Summary of Contents for Telecom Power TBC300A-DCA5

Reviews:

Related manuals for Telecom Power TBC300A-DCA5

Brands by name

Popular brands