Huawei Telecom Power TBC300A-DCA5 User Manual Download Page 58

Page: 58 / 95

TP48200A-HX09A1 and TBC300A-DCA5 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

4.3.2 Identifying Circuit Breaker Faults

The following indicate that the circuit breaker is faulty:



The circuit breaker cannot be switched to ON/OFF after the short circuit fault for its end
circuit is rectified.



When the circuit breaker is switched to ON and its input voltage is normal, the voltage
between the two ends of the circuit breaker exceeds 1 V.



The input voltage is normal, but the resistance between both ends of the circuit breaker is
less than 1 kΩ when the circuit breaker is OFF.

4.3.3 Identifying Rectifier Faults

The following indicate that the rectifier is faulty:



The AC input and slot connector are normal, but the Fault indicator (red) is steady on or
all indicators are off.



The slot connector and SMU are normal, but the Alarm indicator (yellow) still blinks
after the rectifier is reinstalled.



The AC input and SMU are normal, but the SMU cannot control the rectifier.

4.3.4 Identifying SMU Faults

The following indicate that the SMU is faulty:



The DC output is normal but the green indicator on the SMU is off.



The SMU breaks down or cannot be started. Its LCD has abnormal display or buttons
cannot be operated.



With alarm reporting enabled, the SMU does not report alarms when the power system is
faulty.



The SMU reports an alarm when the power system is not faulty.



The SMU fails to communicate with the connected lower-level devices even though the
communications cables are correctly connected.



Communication between the SMU and all rectifiers fails even though the rectifiers and
the communications cables are normal.



The SMU cannot monitor AC or DC power distribution when communications cables are
intact and AC and DC power distribution is normal.



Parameters cannot be set or running information cannot be viewed on the SMU.

4.4 Replacing Components

4.4.1 Replacing a Rectifier

Prerequisites



You have obtained an ESD wrist strap, a pair of protective gloves, an ESD box or bag,
and the cabinet door key.



The new rectifier is intact.

Summary of Contents for Telecom Power TBC300A-DCA5
































































































Search results

Summary of Contents for Telecom Power TBC300A-DCA5

Reviews:

Related manuals for Telecom Power TBC300A-DCA5

Brands by name

Popular brands

Huawei Telecom Power TBC300A-DCA5, User Manual

Search results

Summary of Contents for Telecom Power TBC300A-DCA5

Reviews:

Related manuals for Telecom Power TBC300A-DCA5

Brands by name

Popular brands