manualshive.com logo in svg

Huawei SUN2000-33KTL-A, User Manual, Page: 98 / 117

Share
Download
Huawei SUN2000-33KTL-A User Manual Download Page 98

SUN2000-(33KTL-A, 36KTL, 42KTL) 
User Manual 

8 Maintenance 

 

Issue 07 (2018-05-04) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

92 

 

Alarm 
ID 

Alarm 
Name 

Alarm 
Severity 

Possible Cause 

Suggestion 

The three phases of the 
power grid are seriously 
unbalanced, which triggers 
the protection for the internal 
control circuit of the 
SUN2000. 

 

Cause ID = 11 

The grid voltage changes 
sharply and the SUN2000 
input power fails to discharge 
in a short time, which 
increases the internal voltage 
and triggers overvoltage 
protection. 

 

Cause ID = 12/15 

An unrecoverable fault 
occurs on a circuit inside the 
SUN2000. 

contact Huawei technical support. 

202 

Abnormal 
Invert 
Circuit 

Major 

Abnormal external conditions 
trigger the protection for the 
inverter circuit inside the 
SUN2000. The possible causes 
are as follows: 

 

Cause ID = 13 

The grid voltage drops 
dramatically or the power 
grid is short-circuited, which 
damages the internal voltage 
detection circuit in the 
SUN2000. 

 

Cause ID = 14 

The grid voltage drops 
dramatically or the power 
grid is short-circuited. As a 
result, the inverter transient 
output current exceeds the 
upper threshold and therefore 
the inverter protection is 
triggered. 

 

Cause ID = 16 

The DC current in the power 
grid exceeds the upper 
threshold. 

 

Cause ID = 20 

The inverter output is 
short-circuited. As a result, 
the output current surges to a 
value above the upper limit, 

Cause ID = 13/14/16 

1.

 

The inverter detects its external 
working conditions in real time. 
After the fault is rectified, the 
SUN2000 automatically recovers. 

2.

 

If the alarm persists, contact 
Huawei technical support. 

Cause ID = 20 

1.

 

Check the inverter output cable for 
short-circuits. 

2.

 

If the alarm persists, contact 
Huawei technical support. 

Summary of Contents for SUN2000-33KTL-A






















































































































Reviews:

No comments