manualshive.com logo in svg

Huawei SUN2000-33KTL-A, User Manual, Page: 19 / 117

Share
Download
Huawei SUN2000-33KTL-A User Manual Download Page 19

SUN2000-(33KTL-A, 36KTL, 42KTL) 
User Manual 

2 Overview 

 

Issue 07 (2018-05-04) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

13 

 

 

 

The nameplate figure is for reference only. The actual nameplate prevails. 

Table 2-4

 describes the compliance symbols. 

Table 2-4

 

Compliance symbols 

Symbol 

Name 

Meaning 

 

CQC certification mark 

The SUN2000 has been 
awarded the NB/T 32004 
certification by China 
Quality Certification 
Center (CQC). 

 

RCM certification mark 

The SUN2000 complies 
with RCM certification 
standards. 

 

TÜVRheinland 
certification mark 

The SUN2000 complies 
with TÜVRheinland 
certification standards. 

 

CE certification mark 

The SUN2000 complies 
with Conformité 
Européenne (CE) 
certification standards. 

 

Environmentally friendly 
use period (EFUP) label 

The SUN2000 does not 
pollute the environment 
during the specified 
period. 

 

EU waste electrical and 
electronic equipment 
(WEEE) label 

Do not dispose of the 
SUN2000 as household 
garbage. 

 

2.4 Working Principle 

Conceptual Diagram 

The SUN2000 receives inputs from eight PV strings. Then the inputs are grouped into four 
MPPT routes inside the SUN2000 to track the maximum power point of the PV strings. The 
DC power is then converted into three-phase AC power through an inverter circuit. Surge 
protection is supported on both the DC and AC sides. 

Figure 2-10

 shows the conceptual 

diagram for the SUN2000-33KTL-A/36KTL. 

Figure 2-11

 shows the conceptual diagram for 

the SUN2000-42KTL. 

Summary of Contents for SUN2000-33KTL-A






















































































































Reviews:

No comments