manualshive.com logo in svg

Huawei SUN2000-33KTL-A, User Manual, Page: 67 / 117

Share
Download
Huawei SUN2000-33KTL-A User Manual Download Page 67

SUN2000-(33KTL-A, 36KTL, 42KTL) 
User Manual 

5 Connecting Cables 

 

Issue 07 (2018-05-04) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

61 

 

 

 

DHCP

 is set to 

Disable

 by default. 

 

Ensure that the IP addresses for the SUN2000s and PC are different values in the same network 
segment. 

2.

 

Set 

Modbus TCP

 to 

Client

. Set 

NetEco IP address

, 

NetEco port number

, 

SSL 

encryption

, and 

Key password

 based on site requirements. 

 

 

For operations with the SUN2000 APP, see the 

SUN2000 APP User Manual

. 

 

For operations with the NMS, see the 

iManager NetEco 1000S User Manual

 (iManager NetEco 

1000S V100R002C20 and later). 

Selecting a Communication Mode 

The RS485 and PLC communication modes are mutually exclusive. 

 

If the PLC communication mode is selected, do not connect the RS485 communications 
cable. In addition, you need to set 

PLC communication

 to 

Enable

 on the SUN2000 

APP. 

 

 

The PLC communication mode is only applicable to medium-voltage grid connection 
scenarios and non-low-voltage public grid connection scenarios (industrial environment). 

 

If the RS485 communication mode is selected, do not connect the PLC CCO module to 
the AC power cable. In addition, you are recommended to set 

PLC communication

 to 

Disable

 on the SUN2000 APP. 

 

PLC communication

 is set to 

Enable

 by default. 

5.5.2 Connecting RS485 Communications Cables 

Note 

An RS485 communications cable can be connected in two ways:   

 

Terminal block connection 

You are recommended to use a DJYP2VP2-22 2x2x1 network cable or a 
communications cable with a conductor cross-sectional area of 1 mm

2

 and cable outer 

diameter of 14–18 mm.   

 

RJ45 network port connection 

You are recommended to use a shielded RJ45 connector and a CAT 5E outdoor shielded 
network cable with an outer diameter less than 9 mm and internal resistance not greater 
than 1.5 ohms/10 m. 

 

Select either connection mode during installation. Connecting to a terminal block is recommended. 

 

Summary of Contents for SUN2000-33KTL-A






















































































































Reviews:

No comments