Huawei SUN2000-33KTL-A User Manual Download Page 74

Page: 74 / 117

SUN2000-(33KTL-A, 36KTL, 42KTL)
User Manual

5 Connecting Cables

Issue 07 (2018-05-04)

Huawei Proprietary and Confidential

Figure 5-35

FE communication mode for a single SUN2000



Figure 5-36

shows the communication mode for multiple SUN2000s.

If multiple SUN2000s are used, connect all the SUN2000s in daisy chain mode over a
network cable.

Figure 5-36

FE communication mode for multiple SUN2000s



The FE communication distance between two adjacent SUN2000s on the daisy chain cannot exceed
100 meters.



A daisy chain supports a maximum of 10 SUN2000s to be connected for communication.

RJ45 Connector Pin Definitions

Figure 5-37

shows an RJ45 connector.

Figure 5-37

RJ45 connector

The FE communications cable is connected over standard network cables. A standard network
cable can be 568A or 568B. The network cables used in the same PV grid-tied power

Summary of Contents for SUN2000-33KTL-A






















































































































Search results

Summary of Contents for SUN2000-33KTL-A

Reviews:

Huawei SUN2000-33KTL-A, User Manual, Page: 74 / 117

Search results

Summary of Contents for SUN2000-33KTL-A

Reviews: