Huawei SUN2000-33KTL-A User Manual Download Page 73

Page: 73 / 117

SUN2000-(33KTL-A, 36KTL, 42KTL)
User Manual

5 Connecting Cables

Issue 07 (2018-05-04)

Huawei Proprietary and Confidential

Figure 5-34

Binding communications cables

Step 7

Use a torque wrench with an open end of 33 mm to tighten the locking cap to a torque of 7.5
N•m.

----End

Follow-up Procedure

Check that the cables are connected correctly and securely. Then seal the connectors.

5.5.3 (Optional) Connecting FE Communications Cables

Description

FE communication is mainly used in distributed rooftop scenarios with a small number of
inverters. The inverter can directly connect to the PC over the Ethernet to implement
monitoring networking.

FE communication is optional for the SUN2000-36KTL. To use FE communication, contact local
technical support.



Figure 5-35

shows the communication mode for a single SUN2000.

Summary of Contents for SUN2000-33KTL-A






















































































































Search results

Summary of Contents for SUN2000-33KTL-A

Reviews:

Huawei SUN2000-33KTL-A, User Manual, Page: 73 / 117

Search results

Summary of Contents for SUN2000-33KTL-A

Reviews: