manualshive.com logo in svg

Huawei SUN2000-33KTL-A, User Manual, Page: 17 / 117

Share
Download
Huawei SUN2000-33KTL-A User Manual Download Page 17

SUN2000-(33KTL-A, 36KTL, 42KTL) 
User Manual 

2 Overview 

 

Issue 07 (2018-05-04) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

11 

 

Symbol 

Name 

Meaning 

 

Refer to documentation 

Remind operators to refer 
to the documents shipped 
with the SUN2000. 

 

Grounding 

Indicates the position for 
connecting the protection 
ground cable. 

 

Operation warning 

Do not remove the DC 
input connector when the 
SUN2000 is running. 

 

DC terminal operation 
warning

a

 

High voltage exists after 
the SUN2000 is powered 
on. To avoid electric 
shocks, perform the 
following system 
power-off operations 
before plugging or 
unplugging DC input 
connectors of the 
SUN2000: 

1.

 

Send a shutdown 
command. 

2.

 

Turn off the 
downstream AC 
switch. 

3.

 

Turn off the two DC 
switches at the bottom. 

 

SUN2000 serial number 
label 

Indicates the SUN2000 
serial number. 

Note a: Fittings supplied with the SUN2000s of specific models contain the DC terminal 
operation warning label. You are advised to attach the label at the bottom of the SUN2000 
front side, as shown in 

Figure 2-8

. You can also select an appropriate place for attaching 

the label based on site requirements. 

 

Summary of Contents for SUN2000-33KTL-A






















































































































Reviews:

No comments