Huawei SUN2000-33KTL-A User Manual Download Page 102

Page: 102 / 117

SUN2000-(33KTL-A, 36KTL, 42KTL)
User Manual

8 Maintenance

Issue 07 (2018-05-04)

Huawei Proprietary and Confidential

Alarm
ID

Alarm
Name

Alarm
Severity

Possible Cause

Suggestion

411

AFCI
Self-Check
Failure

Major

Cause ID = 1/2/3

AFCI check fails.

Turn off the AC output switch and
DC input switch. Then turn on the
AC output switch and DC input
switch after 5 minutes. If the fault
persists, contact Huawei technical
support.

Disable the AFCI function if you
are sure not to use it.

412

DC Arc
Fault

Major

Cause ID = 1/2/3/4

The PV string cable is in poor
contact or with open circuits.

Check whether the PV string cable is
in poor contact or with open circuits.
If yes, reconnect the cable.

504

Software
Version
Unmatch

Minor

Cause ID = 1/2/3

During inverter software
upgrade, the version of the
software loaded is incorrect.

Check whether you have performed a
software upgrade recently. If yes,
upgrade the software to the correct
version again.

505

Upgrade
Failed

Major

Cause ID = 1

The upgrade does not end
normally.

Perform the upgrade again.

61440

Flash Fault

Minor

Cause ID = 1



The flash memory is
insufficient.



The flash memory has bad
sectors.

Replace the monitoring board.

If the monitoring board is built
into the monitoring device, replace
the monitoring device.

If you cannot rectify faults with the measures listed in the preceding table, contact Huawei technical
support.

Summary of Contents for SUN2000-33KTL-A






















































































































Search results

Summary of Contents for SUN2000-33KTL-A

Reviews:

Huawei SUN2000-33KTL-A, User Manual, Page: 102 / 117

Search results

Summary of Contents for SUN2000-33KTL-A

Reviews: