Huawei SUN2000-33KTL-A User Manual Download Page 54

Page: 54 / 117

SUN2000-(33KTL-A, 36KTL, 42KTL)
User Manual

5 Connecting Cables

Issue 07 (2018-05-04)

Huawei Proprietary and Confidential

Figure 5-10

Four-core cable (including the ground cable but excluding the neutral wire)

Figure 5-11

Four-core cable (excluding the ground cable but including the neutral wire)

Figure 5-12

Five-core cable (including the ground cable and neutral wire)

Step 5

Insert the exposed core wires into the crimping area of the OT terminal and crimp them using
hydraulic pliers.

One core wire connects to one OT terminal.

Step 6

Wrap the wire crimping area with heat shrink tubing or PVC insulation tape.

If heat shrink tubing is used, put it through the power cable and then crimp the OT terminal.

Step 7

Route the AC output power cable through the AC OUTPUT 1 connector at the bottom of the
chassis.

Summary of Contents for SUN2000-33KTL-A






















































































































Search results

Summary of Contents for SUN2000-33KTL-A

Reviews:

Huawei SUN2000-33KTL-A, User Manual, Page: 54 / 117

Search results

Summary of Contents for SUN2000-33KTL-A

Reviews: