manualshive.com logo in svg

Huawei S3026C-PWR, Installation Manual

Share
Download
Huawei S3026C-PWR Installation Manual Download Page 59

Installation Manual 
Quidway S3026C-PWR Ethernet Switch

 

Chapter 7  Optional Modules

 

7.2.1    Panel and LEDs 

 

 

  Note: 

1000Base-LX module has similar panel as 1000Base-SX module. 1000Base-SX module is used as an 
example in the following.   

 

1000Base-SX module supported on S3026C-PWR has a panel as shown in the 

following figure. 

 

Figure 7-1

 

1000Base-SX module panel 

The following table summarizes the LEDs on the panel.   

Table 7-1

 

LEDs on 1000Base-SX module   

LED Status 

OFF 

The link is down.   

LNK 

ON 

The link is up.   

OFF

 

No packets are being transmitted/received.   

ACT 

Flashing

 

Packets are being transmitted/received.   

 

7.2.2  Interface Fiber 

 

 

  Note: 

ITU recommends defining the optical connector as "Used to connect passive components of two or 
several optical fibers steadily but not permanently" (approved by the VI research team of CCITT in 
March, 1992 in Geneva). 
Optical connectors are indispensable passive components in optical fiber communication system. Their 
application enables the removable connection between light paths. 

Huawei Technologies Proprietary 

7-2

 

Summary of Contents for S3026C-PWR

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands