manualshive.com logo in svg

Huawei S3026C-PWR, Installation Manual

Share
Download
Huawei S3026C-PWR Installation Manual Download Page 42

Installation Manual 
Quidway S3026C-PWR Ethernet Switch

 

Chapter 5    Loading BOOTROM and Host Software

 

Huawei Technologies Proprietary 

5-1

 

Chapter 5  Loading BOOTROM and Host Software 

5.1  Loading Approaches 

S3026C-PWR support both local and remote software loading.   

Remote loading:   

z

 

Using FTP 

z

 

Using TFTP 

Local loading:   

z

 

Using XModem and through Console port 

z

 

Using TFFP and through Ethernet port 

z

 

Using FTP and through Ethernet port 

 

 

  Note: 

You must load the Boot ROM and host software in the versions that match each other.   

 

5.2  Local Loading 

After correctly connecting a user terminal to the switch, you can load locally the Boot 

ROM and host software of the switch.   

 

 

  Note: 

The loading process of Boot ROM is similar to that of host software, only the system gives different 
prompts after you press Ctrl + U when entering the Boot menu. The following description is based on 
the loading of Boot ROM.   

 

5.2.1  Boot Menu 

The Boot menu of S3026C-PWR is as follows:   

Starting... 

Summary of Contents for S3026C-PWR

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands