Huawei Iris Hellas SUN2000 Series User Manual Download Page 74

Page: 74 / 123

No.

Parameter

Description

Startup frequency upper

threshold of grid

connection (Hz)

According to the standards of certain countries and

regions, after the inverter is powered on for the first time

for grid connection, if the power grid voltage is higher

than

Startup frequency upper threshold of grid

connection

, the inverter is not allowed to connect to the

grid.

Startup frequency lower

threshold of grid

connection (Hz)

According to the standards of certain countries and

regions, after the inverter is powered on for the first time

for grid connection, if the power grid voltage is lower

than

Startup frequency lower threshold of grid

connection

, the inverter is not allowed to connect to the

grid.

Grid reconnection voltage

upper limit (V)

The standards of certain countries and regions require

that after the inverter shuts down for protection due to a

fault, if the power grid voltage is higher than

Grid

reconnection voltage upper limit

, the inverter is not

allowed to reconnect to the grid.

Grid reconnection voltage

lower limit (V)

The standards of certain countries and regions require

that after the inverter shuts down for protection due to a

fault, if the power grid voltage is lower than

Grid

reconnection voltage lower limit

, the inverter is not

allowed to reconnect to the grid.

Grid reconnection frequency

upper limit (Hz)

The standards of certain countries and regions require

that after the inverter shuts down for protection due to a

fault, if the power grid frequency is higher than

Grid

reconnection frequency upper limit

, the inverter is not

allowed to reconnect to the grid.

Grid reconnection frequency

lower limit (Hz)

The standards of certain countries and regions require

that after the inverter shuts down for protection due to a

fault, if the power grid frequency is lower than

Grid

reconnection frequency lower limit

, the inverter is not

allowed to reconnect to the grid.

Reactive power

compensation (cosφ-P)

trigger voltage (%)

Specifies the voltage threshold for triggering reactive

power compensation based on the cosφ-P curve.

Reactive power

compensation (cosφ-P) exit

voltage (%)

Specifies the voltage threshold for exiting reactive power

compensation based on the cosφ-P curve.

SUN2000-(175KTL-H0, 185KTL-INH0, 185KTL-H1

User Manual

7 Man-Machine Interactions

Issue 05 (2020-08-30)

Summary of Contents for Iris Hellas SUN2000 Series




























































































































Search results

Summary of Contents for Iris Hellas SUN2000 Series

Reviews:

Related manuals for Iris Hellas SUN2000 Series

Brands by name

Popular brands

Huawei Iris Hellas SUN2000 Series, User Manual

Search results

Summary of Contents for Iris Hellas SUN2000 Series

Reviews:

Related manuals for Iris Hellas SUN2000 Series

Brands by name

Popular brands