Huawei Iris Hellas SUN2000 Series User Manual Download Page 71

Page: 71 / 123

No.

Parameter

Description

Remarks

Automatic OFF

due to

communication

interrupted

The standards of certain countries

and regions require that the

inverter must shut down after the

communication is interrupted for

a certain time.

Automatic OFF due to

communication interrupted

set to

Enable

and the inverter

communication is interrupted

for a specified time (set by

Communication interruption

duration

), the inverter will

automatically shut down.

Automatic ON due

to communication

resumed

If this parameter is set to

Enable

the inverter automatically starts

after communication recovers. If

this parameter is set to

Disable

the inverter needs to be started

manually after communication

recovers.

This parameter is displayed

when

Automatic OFF due to

communication interrupted

set to

Enable

Communication

interruption

duration (min)

Specifies the duration for

determining communication

interruption. Used for automatic

shutdown for protection in case of

communication interruption.

Soft start/boot

time (s)

Specifies the duration for the

power to gradually increase when

the inverter starts.

Shutdown gradient

(%/s)

Specifies the power change speed

when the inverter shuts down.

Night-time

hibernation

The inverter monitors PV strings

at night. If this parameter is set to

Enable

, the monitoring function

of the inverter will hibernate at

night to reduce power

consumption.

MBUS

communication

For inverters that support RS485

communication and MBUS

communication, you are advised

to set this parameter to

Disable

to reduce power consumption.

Delay upgrade

This parameter is mainly used in

the upgrade scenarios where the

PV power supply is disconnected

at night due to no sunlight or

unstable at dawn or dusk due to

poor sunlight.

After the inverter starts to

upgrade, if

Delay upgrade

set to

Enable

, the upgrade

package is loaded first. After

the PV power supply recovers

and the activation conditions

are met, the inverter

automatically activates the

upgrade.

SUN2000-(175KTL-H0, 185KTL-INH0, 185KTL-H1

User Manual

7 Man-Machine Interactions

Issue 05 (2020-08-30)

Summary of Contents for Iris Hellas SUN2000 Series




























































































































Search results

Summary of Contents for Iris Hellas SUN2000 Series

Reviews:

Related manuals for Iris Hellas SUN2000 Series

Brands by name

Popular brands

Huawei Iris Hellas SUN2000 Series, User Manual

Search results

Summary of Contents for Iris Hellas SUN2000 Series

Reviews:

Related manuals for Iris Hellas SUN2000 Series

Brands by name

Popular brands