Huawei Iris Hellas SUN2000 Series User Manual Download Page 105

Page: 105 / 123

Alarm

Alarm Name

Alarm

Severity

Cause

Troubleshooting Suggestions

2086

External fan

abnormal

Major

External fan short-

circuited, power supply

insufficient, or air channel

blocked
Cause ID 1–3: fans 1–3

1. Shut down the fan, turn off

the DC switch, check

whether the fan blades are

damaged, and clear the

foreign matter around the

fan.

2. Reinstall the fan, turn on

the DC switch, and wait for

the inverter to start. If the

fault persists after 15

minutes, replace the

external fan.

2087

Internal fan

abnormal

Major

Cause ID=1
The internal fan is short-

circuited, the power supply

is insufficient, or the fan is

damaged.

Turn off the AC output switch

and then the DC input switch.

Turn them on after 5 minutes

and wait for the inverter to

connect to the power grid. If

the fault persists, contact your

dealer or Huawei technical

support.

61440 Faulty

Monitoring

Unit

Minor

Cause ID=1
1. The flash memory is

insufficient.

2. The flash memory has

bad sectors.

Turn off the AC output switch

and DC input switch, and then

turn them on after 15

minutes. If the fault persists,

replace the monitoring board

or contact your dealer or

Huawei technical support.

NO TE

If you cannot rectify faults with the measures listed in troubleshooting suggestions, contact

your dealer or Huawei technical support.

SUN2000-(175KTL-H0, 185KTL-INH0, 185KTL-H1

User Manual

8 Maintenance

Issue 05 (2020-08-30)

Summary of Contents for Iris Hellas SUN2000 Series




























































































































Search results

Summary of Contents for Iris Hellas SUN2000 Series

Reviews:

Related manuals for Iris Hellas SUN2000 Series

Brands by name

Popular brands

Huawei Iris Hellas SUN2000 Series, User Manual

Search results

Summary of Contents for Iris Hellas SUN2000 Series

Reviews:

Related manuals for Iris Hellas SUN2000 Series

Brands by name

Popular brands