Huawei iBattery 3.0 User Manual Download Page 16

Page: 16 / 89

iBattery 3.0
User Manual

2 Overview

Issue 07 (2019-12-30)

Pin Definition Signal

Description

Status

Description

Initial Status

Remarks

12 V driving
signals

signal for
BCB
tripping.



12 V:
There is a
driving
signal for
BCB
tripping.

GND

Secondary side
ground

Table 2-8

BCB_IN and BCB_OUT cascading port pin definitions

Pin

Definition BCB_IN Signal

Description

BCB_OUT

Signal
Description

Status

Description

Initial

Status

Description

Specifies
whether the BCB
connects to the
signal output
port.

Specifies
whether the
cascaded
BCBs
connect to the
signal input
port.



Grounded:
BCB
connected.



Disconnected
: BCB not
connected.

Disconnected

Receives
BCB
commands
sent by the
UPS and
supports BCB
port
cascading
management.

STA

Signal output
port for the
battery circuit
breaker status

Monitors
whether the
cascaded
BCBs are
connected to
the input.



Grounded:
The battery
circuit
breaker is
ON.



Disconnected
: The battery
circuit
breaker is
OFF.

Disconnected

DRV

Controls battery circuit breaker
trip and receives 12 V driving
signals



0 V: There is
no driving
signal for
BCB tripping.



12 V: There
is a driving
signal for
BCB tripping.

0 V

GND

Secondary side ground

Summary of Contents for iBattery 3.0


























































































Search results

Summary of Contents for iBattery 3.0

Reviews:

Related manuals for iBattery 3.0

Brands by name

Popular brands

Huawei iBattery 3.0, User Manual

Search results

Summary of Contents for iBattery 3.0

Reviews:

Related manuals for iBattery 3.0

Brands by name

Popular brands