Huawei BTS3900 V100R003 Hardware Description Download Page 9

Page: 9 / 264

Contents

About This Document...................................................................................................................iii

1 Changes in the BTS3900 Hardware Description..................................................................1-1

2 Exterior of the BTS3900 Cabinet..............................................................................................2-1

3 BTS3900 Hardware Configuration..........................................................................................3-1

3.1 Board and Module Configurations..................................................................................................................3-2

3.1.1 Module Configurations in the Cabinet...................................................................................................3-2
3.1.2 Board Configurations of the BBU3900..................................................................................................3-5

3.2 Combinations of Cabinets.............................................................................................................................3-14
3.3 Power System of the BTS3900.....................................................................................................................3-18

3.3.1 Configurations of the Upper-Level Circuit Breaker and Power Cables...............................................3-19
3.3.2 Power Distribution of the BTS3900.....................................................................................................3-20

3.4 Transmission Board Configurations..............................................................................................................3-22
3.5 CPRI Port Configurations.............................................................................................................................3-23

3.5.1 CPRI Port Specifications......................................................................................................................3-23
3.5.2 Configuration Principles for the CPRI Ports on the RFU in the GSM Only Base Station..................3-25
3.5.3 Configuration Principles for the CPRI Ports on the RFU in the UMTS Only Base Station................3-27
3.5.4 Configuration Principles for the CPRI Ports on the RFU in the LTE Only Base Station....................3-29
3.5.5 Configuration Principles for the CPRI Ports on the RFU in the GSM+UMTS Base Station..............3-31
3.5.6 Configuration Principles for the CPRI Ports on the RFU in the GSM+LTE Base Station..................3-33
3.5.7 Configuration Principles for the CPRI Ports on the RFU in the UMTS+LTE Base Station...............3-35

3.6 BTS3900 Monitoring System........................................................................................................................3-36

3.6.1 BBU Monitoring Port...........................................................................................................................3-36
3.6.2 Monitoring Principles of the Cabinet ..................................................................................................3-37
3.6.3 Customized Alarm Inputs.....................................................................................................................3-39

3.7 RF Configurations.........................................................................................................................................3-41

BTS3900
Hardware Description

Contents

Issue 04 (2011-02-15)

Huawei Proprietary and Confidential

vii

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands