Huawei BTS3900 V100R003 Hardware Description Download Page 139

Page: 139 / 264

Multiplexes the RX and TX signals of the RF channels.

Enables the TX and RX signals to share the same antenna channel.

Filters the RX and TX signals.

LEDs

There are six LEDs on the panel of the DRFU, indicating its operating status.

Table 4-48

describes the status of the LEDs on the DRFU.

Table 4-48

Status of the LEDs on the DRFU

LED

Color

State

Meaning

RUN

Green

There is power supply, but the module
is faulty.

On for 1s and off for 1s The module is functional.

On for 0.125s and off
for 0.125s

The module is loading software or is not
started.

Off

There is no power supply, or the module
is faulty.

ALM

Red

Alarms are generated, and the module
needs to be replaced.

On for 1s and off for 1s Alarms are reported. The alarms may

be caused by the faults of the related
boards or ports. Therefore, whether the
module needs to be replaced cannot be
decided.

Off

No alarm is generated.

ACT

Green

The board works properly with the TX
channel enabled.

On for 1s and off for 1s The module works properly with the

TX channel disabled.

VSWR

Red

The VSWR alarm is generated on the
ANT1 port.

On for 1s and off for 1s The VSWR alarm is generated on the

ANT2 port.

On for 0.125s and off
for 0.125s

The VSWR alarm is generated on the
ANT1 and ANT2 ports.

Off

No VSWR alarm is reported.

CPRI0

Red/Green

Steady green

The CPRI link is functional.

Steady red

The optical module fails to receive
signals.

BTS3900
Hardware Description

4 BTS3900 Components

Issue 04 (2011-02-15)

Huawei Proprietary and Confidential

4-47

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands