Huawei BTS3900 V100R003 Hardware Description Download Page 111

Page: 111 / 264

Table 4-17

LEDs on the WBBP and their status

Label

Color

Status

Description

RUN

Green

The board has power input, yet
the board is faulty.

OFF

The power supply or the board
is faulty.

Blinking (on for one second
and off for one second)

The board is running properly.

Blinking (on for 0.125 second
and off for 0.125 second)

Software is being loaded to the
board.

ACT

Green

The board is running properly.

OFF

The WBBP is not in use.

ALM

Red

OFF

The board is running properly.

The board has hardware alarms.

The WBBPa or WBBPb provides three LEDs indicating the status of the SFP links. The LEDs
are positioned below the SFP ports. The WBBPd provides six LEDs indicating the status of the
SFP links. The LEDs are positioned above the SFP ports.

Table 4-18

describes the LEDs.

Table 4-18

LEDs indicating the status of the SFP links

Label

Color

Status

Description

TX RX

Red/Green

Steady green

The CPRI link is
available.

Steady red

The optical module
fails to receive
signals.

Blinking red (ON for
0.125 second and
OFF for 0.125
second)

The RRU on the
CPRI link is faulty.

Blinking red (ON for
one second and OFF
for one second)

The CPRI link is out
of lock.

OFF

The SFP module is
not in position or the
optical module is
powered off.

BTS3900
Hardware Description

4 BTS3900 Components

Issue 04 (2011-02-15)

Huawei Proprietary and Confidential

4-19

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands