Huawei BTS3900 V100R003 Hardware Description Download Page 140

Page: 140 / 264

LED

Color

State

Meaning

On for 1s (red) and off
for 1s

The CPRI link is out of lock.

Off

The SFP module is not in position or the
optical module is powered off.

CPRI1

Red/Green

Steady green

The CPRI link is functional.

Steady red

The optical module fails to receive
signals.

On for 1s (red) and off
for 1s

The CPRI link is out of lock.

Off

The SFP module is not in position or the
optical module is powered off.

Ports

Table 4-49

describes the ports and sockets on the DRFU.

Table 4-49

Ports and sockets on the DRFU

Port

Connector

Label

Description

Port for
transceiving
RF signals

DIN female

ANT1

Connecting to the antenna system

ANT2

CPRI port

SFP female

CPRI0

Connecting to the lower-level RFU
during the cascading

CPRI1

Connecting to the BBU, or the upper-
level RFU in cascading mode

Interconnecti
on port for
receiving RF
signals

QMA female

RX1/IN

Diversity RX port in antenna channel 1

RX1/OUT

Diversity TX port in antenna channel 1

RX2/IN

Diversity RX port in antenna channel 2

RX2/OUT

Diversity TX port in antenna channel 2

Power supply
socket

3V3

PWR

Used to lead in power

QMA

QMA female

FIXED

Unique port of the DRFU of 1800 MHz,
which is used to switch between the
combined transmission and divided
transmission modes

UNCOMB

COMB

4 BTS3900 Components

BTS3900

Hardware Description

4-48

Huawei Proprietary and Confidential

Issue 04 (2011-02-15)

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands