Huawei BTS3900 V100R003 Hardware Description Download Page 126

Page: 126 / 264

Label

Color

Status

Description

ALM

Red

ON or blinking
rapidly

The board is
reporting alarms.

OFF

The board is running
properly.

ON for 2s and OFF
for 2s

The board is
reporting a minor
alarm.

ON for 1s and OFF
for 1s

The board is
reporting a major
alarm.

ON for 0.125s and
OFF for 0.125s

The board is
reporting a critical
alarm.

ACT

Green

The board is in active
mode.

OFF

The board is in
standby mode.

UTRP2 and UTRP9 provide two LEDs for indicating the status of the current link.

Table

4-35

describes the LEDs on the Ethernet ports of the UTRP2 and UTRP9.

Table 4-35

LEDs on the Ethernet ports of the UTRP2 and UTRP9

Label

Color

Status

Description

LINK

Green

OFF

The link is
disconnected.

The link is properly
connected.

ACT

Orange

Blinking

The link is receiving
or transmitting data.

OFF

The link is not
receiving or
transmitting data.

Ports

Table 4-36

describes the ports of the UTRP2 supporting two optical ports.

4 BTS3900 Components

BTS3900

Hardware Description

4-34

Huawei Proprietary and Confidential

Issue 04 (2011-02-15)

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands