Huawei BTS3900 V100R003 Hardware Description Download Page 147

Page: 147 / 264

–

Encapsulate data

The downlink TX channel has the following functions:

–

Decapsulates the clock signals, control signals and data signals from the BBU and sends
them to associated units

–

Shapes and filters downlink signals

–

Performs digital-to-analog conversion and IF output of IQ analog signals

–

Performs orthogonal up-conversion of IF signals to the TX band

The power amplifier amplifies the low-power RF signals from the signal processing unit.

The duplexer has the following functions:

Multiplexes the RX signals and TX signals

Combines the RX signals and TX signals so that they share the same antenna channel

Filters the RX/TX signals

LEDs

Table 4-52

describes the LEDs on the panel of the MRFU.

Table 4-52

LEDs on the panel of the MRFU

Label

Color

Status

Description

RUN

Green

The power input is normal, and the
module is faulty.

Off

There is no power input, or the module
is faulty.

On for 1s and off for 1s The module runs properly.

On for 0.125s and off
for 0.125s

The module is loading software or is
not started.

ALM

Red

An alarm is generated, and the module
needs to be replaced.

Blinking (on for 1s and
off for 1s)

An alarm is generated. The alarm may
be caused due to faults in the related
boards or ports. Therefore, whether the
module needs to be replaced cannot be
determined.

Off

No alarm is generated.

ACT

Green

The module works properly (TX
channel enabled).

On for 1s and off for 1s The module is running (TX channel

disabled).

VSWR

Red

On (red)

A VSWR-related alarm is generated at
the ANT_TX/RXA port.

BTS3900
Hardware Description

4 BTS3900 Components

Issue 04 (2011-02-15)

Huawei Proprietary and Confidential

4-55

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands