Huawei BTS3900 V100R003 Hardware Description Download Page 16

Page: 16 / 264

Power cable connections of the BTS3900 (220 V)..........................................................................5-11

Figure 5-4

E1/T1 cable connections...................................................................................................................5-12

Figure 5-5

E1/T1 cable connections...................................................................................................................5-12

Figure 5-6

FE/GE Ethernet cable connections...................................................................................................5-13

Figure 5-7

FE/GE optical cable connections......................................................................................................5-13

Figure 5-8

E1/T1 cable connections (1).............................................................................................................5-14

Figure 5-9

E1/T1 cable connections (2).............................................................................................................5-14

Figure 5-10

FE/GE Ethernet cable connections (1)........................................................................................... 5-15

Figure 5-11

FE/GE Ethernet cable connections (2)........................................................................................... 5-15

Figure 5-12

FE/GE optical cable connections (1)..............................................................................................5-15

Figure 5-13

FE/GE optical cable connections (2)..............................................................................................5-16

Figure 5-14

E1/T1 cable connections.................................................................................................................5-16

Figure 5-15

FE/GE optical cable connections....................................................................................................5-17

Figure 5-16

Transmission cable connection for a GSM+UMTS base station in TDM common transmission mode

(1)........................................................................................................................................................................5-17

Figure 5-17

Transmission cable connection for a GSM+UMTS base station in TDM common transmission mode

(2)........................................................................................................................................................................5-18

Figure 5-18

Transmission cable connections for a GSM+UMTS base station in IP over E1 common transmission

mode (1).............................................................................................................................................................. 5-18

Figure 5-19

Transmission cable connections for a GSM+UMTS base station in IP over E1 common transmission

mode (2).............................................................................................................................................................. 5-19

Figure 5-20

Transmission cable connections for a GSM+UMTS base station in IP over FE common transmission

mode (1).............................................................................................................................................................. 5-19

Figure 5-21

Transmission cable connections for a GSM+UMTS base station in IP over FE common transmission

mode (2).............................................................................................................................................................. 5-20

Figure 5-22

Transmission cable connections with FE optical ports for interconnection and FE electrical ports

connected to the BSC and RNC..........................................................................................................................5-21

Figure 5-23

Transmission cable connections with FE electrical ports for interconnection and FE optical ports

connected to the BSC and RNC..........................................................................................................................5-21

Figure 5-24

E1/T1 cable connections in separate transmission mode............................................................... 5-22

Figure 5-25

FE/GE cable connections in separate transmission mode (1).........................................................5-22

Figure 5-26

FE/GE cable connections in separate transmission mode (2).........................................................5-23

Figure 5-27

Transmission cable connections for a GSM+LTE base station in IP over E1 common transmission

mode (1).............................................................................................................................................................. 5-23

Figure 5-28

Transmission cable connections for a GSM+LTE base station in IP over E1 common transmission

mode (2).............................................................................................................................................................. 5-24

Figure 5-29

Transmission cable connections for a GSM+LTE base station in IP over FE/GE common transmission

mode (1).............................................................................................................................................................. 5-24

Figure 5-30

Transmission cable connections for a GSM+LTE base station in IP over FE/GE common transmission

mode....................................................................................................................................................................5-25

Figure 5-31

Transmission cable connections with FE electrical ports for interconnection and FE optical ports

connected to the base station controller.............................................................................................................. 5-26

Figure 5-32

Transmission cable connections with FE optical ports for interconnection and FE electrical ports

connected to the base station controller.............................................................................................................. 5-26

Figure 5-33

Transmission cable connections in a base station in GSM 4E1/T1+LTE FE/GE mode (1).......... 5-27

Figure 5-34

Transmission cable connections in a base station in GSM 4E1/T1+LTE FE/GE mode (2).......... 5-28

Figures

BTS3900

Hardware Description

xiv

Huawei Proprietary and Confidential

Issue 04 (2011-02-15)

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands