Huawei BTS3900 V100R003 Hardware Description Download Page 72

Page: 72 / 264

When a base station works in UMTS+LTE mode, the RFU slot assignment in a cabinet must
comply with specific principles.

3.7.1 RFU Configurations

The RFUs configured in a base station can be MRFUs, DRFUs, GRFUs, WRFUs, or LRFUs.

Table 3-26

describes RFU configurations.

Table 3-26

RFU configurations

Mode

Frequency
Band

Supported
RFU

Maximum
Number of
Supported
Carriers

Number of TX
and RX
Channels

GSM only (GO) EGSM 900

MHz

DRFU/GRFU/
MRFU V1/
MRFU V2

2 carriers
(DRFU)

6 carriers
(GRFU)

6 carriers
(MRFU V1/
MRFU V2)

2T2R
(DRFU)

1T2R
(GRFU)

1T2R
(MRFU V1/
MRFU V2)

PGSM 900
MHz

DRFU/GRFU/
MRFU V1/
MRFU V2

GSM 1800 MHz DRFU/GRFU/

MRFU V1/
MRFU V2

GSM 1900 MHz GRFU/MRFU

UMTS only
(UO)

850 MHz

WRFU

2 or 4
carriers
(WRFU)

4 carriers
(MRFU V1/
MRFU V2)

1T2R
(WRFU)

1T2R
(MRFU V1/
MRFU V2)

900 MHz

MRFU V1/
MRFU V2

2100 MHz

WRFU

LTE only (LO)

AWS

LRFU

1 carrier
(LRFU)

1 carrier
(MRFU V2)

2T2R
(LRFU)

1T2R
(MRFU)

2600 MHz

900 MHz

MRFU V2

1800 MHz

GSM+UMTS
(GU)

MRFU V1/
MRFU V2

A base station
working in
GSM+UMTS
mode supports a
maximum of six
carriers, and a
maximum of
two carriers are
supported by the
UMTS side.

1T2R

3 BTS3900 Hardware Configuration

BTS3900

Hardware Description

3-42

Huawei Proprietary and Confidential

Issue 04 (2011-02-15)

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands