HS-Technik RoboRiv Operating Instructions Manual Download

Page: 58 / 64

Declaration of conformity in accordance with the

electromagnetic compatibility directive 2014/30/EU

We, the manufacturer, hereby declare that the named tool complies with the essential

protection requirements of the listed EU directives regarding design and construction

type.

The prerequisite for this is the intended use of the tool as well as compliance with the

installation and commissioning instructions.

If the product or its accessories are modified without our consent, this declaration be

comes invalid.

Tool description:

Programmable cordless blind riveting tool

Type designation:

RoboRiv®

Manufacturer:

HS-Technik GmbH

Im Martelacker 12

D-79588 Efringen-Kirchen

Directives:

2014/30/EU

Applied standards:

EN 61000-6-3:2007+A1:2011+AC:2012

EN 61000-6-2:2005+ AC:2005

EN 55014-1:2006+A1:2009+A2:2011

EN 55014-2:1997+ AC:1997+A1:2001+A2:2008

HS-Technik GmbH

Im Martelacker 12, D-79588 Efringen-Kirchen

April 2020

Florian Hanke

CEO

Summary of Contents for RoboRiv

































































Search results

Summary of Contents for RoboRiv

Reviews:

Related manuals for RoboRiv

Brands by name

Popular brands

HS-Technik RoboRiv, Operating Instructions Manual

Search results

Summary of Contents for RoboRiv

Reviews:

Related manuals for RoboRiv

Brands by name

Popular brands