HS-Technik RoboRiv Operating Instructions Manual Download

Page: 59 / 64

EC Declaration of Incorporation according to Machinery

Directive 2006/42/EC, Annex II, 1. B

We as the manufacturer hereby declare that the specified device corresponds in terms

of design and construction type to the following protection requirements according to

Annex I of EC Machinery Directive 2006/42/EC.

The prerequisite for this is the intended use of the tool as well as compliance with the

installation and commissioning instructions.

If the product or its accessories are modified without our consent, this declaration be

comes invalid.

Tool description:

Programmable cordless blind riveting tool

Type designation:

RoboRiv®

Manufacturer:

HS-Technik GmbH

Im Martelacker 12

D-79588 Efringen-Kirchen

Directives:

2006/42/EC

Applied standards:

EN 62841-1:2015+AC:2015, EN 62841-2-2:2014

HS-Technik GmbH

Im Martelacker 12, D-79588 Efringen-Kirchen

April 2020

Florian Hanke

CEO

Summary of Contents for RoboRiv

































































Search results

Summary of Contents for RoboRiv

Reviews:

Related manuals for RoboRiv

Brands by name

Popular brands

HS-Technik RoboRiv, Operating Instructions Manual

Search results

Summary of Contents for RoboRiv

Reviews:

Related manuals for RoboRiv

Brands by name

Popular brands