HPE 5820X Series Configuration Manual Download Page 434 | Manualshive

Page: 434 / 512

background image

422

Step

Command

Remarks

3.

Configure an RD for the VPN
instance.

route-distinguisher

route-distinguisher

Not configured by default.

4.

Enable IPv6 multicast
routing.

multicast ipv6 routing-enable

Disabled by default.

5.

Enter interface view.

interface

interface-type

interface-number

N/A

6.

Bind the interface with a VPN
instance.

ip binding vpn-instance

vpn-instance-name

By default, an interface belongs to
the public network, and is not
bound with any VPN instance.

7.

Enable IPv6 PIM-SM.

pim ipv6 sm

Disabled by default.

For more information about the

ip vpn-instance

,

route-distinguisher

, and

ip binding

vpn-instance

commands, see

MPLS Command Reference

.

Configuring an RP

CAUTION:

When both IPv6 PIM-SM and IPv6 BIDIR-PIM run on the IPv6 PIM network, do not use the same RP
to serve IPv6 PIM-SM and IPv6 BIDIR-PIM. Otherwise, exceptions might occur to the IPv6 PIM
routing table.

An RP can be manually configured or dynamically elected through the BSR mechanism. For a large
IPv6 PIM network, static RP configuration is a tedious job. Generally, static RP configuration is just a
backup method for the dynamic RP election mechanism to enhance the robustness and operation
manageability of a multicast network.

Configuring a static RP

If only one dynamic RP exists in a network, manually configuring a static RP can avoid
communication interruption because of single-point failures. It can also avoid frequent message
exchange between C-RPs and the BSR.

To enable a static RP to work normally, you must perform this configuration on all routers in the IPv6
PIM-SM domain and specify the same RP address.

To configure a static RP:

Step Command

Remarks

1.

Enter system view.

system-view

N/A

2.

Enter public network IPv6
PIM view or VPN instance
IPv6 PIM view.

pim ipv6

[

vpn-instance

vpn-instance-name

]

N/A

3.

Configure a static RP for
IPv6 PIM-SM.

static-rp

ipv6-rp-address

[

acl6-number

] [

preferred

]

No static RP by default.

Configuring a C-RP

In an IPv6 PIM-SM domain, you can configure routers that intend to become the RP as C-RPs. The
BSR collects the C-RP information by receiving the C-RP-Adv messages from C-RPs or auto-RP
announcements from other routers and organizes the information into an RP-set, which is flooded
throughout the entire network. Then, the other routers in the network calculate the mappings
between specific group ranges and the corresponding RPs based on the RP-Set. Hewlett Packard
Enterprise recommends you configure C-RPs on backbone routers.

«
...
432
433
434
435
436
...
»

Summary of Contents for 5820X Series

































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5820X Series

Brand: D-Link Pages: 357

Brand: KELCO Pages: 22

Brand: OFFICINE OROBICHE Pages: 7

Brand: UNICOM Pages: 1

Edge RTM-ATCA-F140

Brand: Penguin Pages: 2

DL-DVI-MUX2-NT SERIES

Brand: G&D Pages: 76

SI1P-SH-DVI-UCAC

Brand: Black Box Pages: 16

Brand: Madison Pages: 2

Brand: H3C Pages: 96

Brand: NVision Pages: 86

Brand: Versa Technology Pages: 26

IDS-105FE Series

Brand: Perle Pages: 2

Brand: Optone Pages: 10

Brand: Banner Pages: 8

Brand: InvoTek Pages: 4

Brand: Led Control Pages: 22

Brand: Cables to Go Pages: 3

Brand: CCTVMule Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands