manualshive.com logo in svg

HP Visualize J200, Reference Manual

The HP Visualize J200 Reference Manual is a comprehensive user guide that provides step-by-step instructions and detailed information on operating and maximizing the full potential of your HP Visualize J200. Download this manual for free from manualshive.com to access everything you need to know about this powerful product.

Share
Download
background image

   

   

PS/2

The keyboard and mouse interfaces are implemented by simple serial ports conforming to the defacto
industry standard PS/2 specification. Both the keyboard and mouse have a dedicated serial port of their
own. The interface ports rely on the software to provide all of their intelligence; therefore, they do not
interpret the characters passing through them in either direction. The interface to the host processor is
through 6 one–byte registers for each port. The keyboard and mouse are connected to the system via
standard PC–style, miniature DIN connectors. The keyboard is a PC compatible 101 and 102 key layout
PS/2–style with a cable length of 7.5 feet. The 3–button mouse (A2839A) comes with a 9 foot cable. The
mouse can be ordered separately. We do not recommend extending the keyboard or mouse cables beyond
15 feet, due to signal degradation.

Central Processing Units

This section describes the J Class CPUs, processor module, and cache memory.

CPU

General Overview

The PA7200 CPU module is designed to work with J Class workstations. It offers the next step in
performance after the 7150 PCX–T based module. Not only does it offer a higher performance processor,
the bus interface also provides higher bandwidth than its predecessor. Finally, the bus and processor
support symmetric multi–processing, and hardware based cache coherency. The CPU module consists of
a processor, split Instruction and Data cache, and a bus interface. Different performance points can be
achieved by adjusting three factors: processor clock frequency, bus clock frequency, and cache size.

Introduction

The electrical interface between the CPU module and the rest of the system is composed of power, clocks,
the interconnect bus interface, and test interface. Most power and ground and all logical signals are routed
through an impedance controlled Micropax connector. The two remaining power sources, VDH and VDL
are routed through 2 Metral power connectors. Identification of the module clock rate, cache size, and
processor voltage requirements are provided with static lines, hardwired on the module.

Signal Description

Micropax and Metral Power Connectors

The CPU module has 2 Metral power connectors and a single 200–pin Berg Micropax connector as its
external system interface.

The 2 Metral power connectors receive Vdh and Vdl from the external system. Each Metral power
connector consists of two receptacles. In the J Class systems, only one power receptacle is used at any one
time. The Metral connectors also serve as alignment pins to guide the CPU module onto the system board.

Vdd and all logical connections are connected through the 200–pin Micropax connector. The signal pad
pitch is 25 mils and the pads are placed in 2 rows in an offset pattern. There are 124 logical signal pins, 16
Vdd pins, 57 Ground pins, and 2 +12 volt and 1 no connect (spare). The signal to ground ratio is 2:1.

Please refer to Table 2–4 for a summary of the interface signals and power bus. Also, refer to the
Micropax Connector Pinout.

Summary of Contents for Visualize J200




































































































Reviews:

No comments

Related manuals for Visualize J200

Nidec Leroy-Somer R180 Installation And Maintenance Manual preview
Leroy-Somer R180
Brand: Nidec Pages: 20
Lattice Semiconductor CrossLink Programming And Configuration Manual preview
CrossLink
Brand: Lattice Semiconductor Pages: 30
WAFER DC200 Manual preview
DC200
Brand: WAFER Pages: 15
KEENZ Class Instruction Manual preview
Class
Brand: KEENZ Pages: 24
Panasonic Minas A4 Series Connection Manual preview
Minas A4 Series
Brand: Panasonic Pages: 5
Samson 3354 Mounting And Operating Instructions preview
3354
Brand: Samson Pages: 40
Häfele 633.03.298 Quick Start Manual preview
633.03.298
Brand: Häfele Pages: 2
Häfele 633.03.298 Operating Instructions Manual preview
633.03.298
Brand: Häfele Pages: 24
Maclaren Major Elite Manual preview
Major Elite
Brand: Maclaren Pages: 43
Lawler 804 Installation & Maintenance Manual preview
804
Brand: Lawler Pages: 5
DigiPower IPP-S Series Installation Manual preview
IPP-S Series
Brand: DigiPower Pages: 27
GEA SIMATIC C7-623 Instruction Manual preview
SIMATIC C7-623
Brand: GEA Pages: 13
EMS ZITON RADIO LOOP MODULE Programming Manual preview
ZITON RADIO LOOP MODULE
Brand: EMS Pages: 26
Danfoss 084B8012 Instructions Manual preview
084B8012
Brand: Danfoss Pages: 30
Burlington SP697 Installation Instruction preview
SP697
Brand: Burlington Pages: 7
HEIDENHAIN ND 1300 Operating Instructions Manual preview
ND 1300
Brand: HEIDENHAIN Pages: 257
Widex RC4-1 User Instructions preview
RC4-1
Brand: Widex Pages: 17
Zencontrol zc-controller Instructions preview
zc-controller
Brand: Zencontrol Pages: 2

Brands by name

Popular brands

Load more brands