HP ProLiant DL60 Gen9 User Manual Download Page 4

Page: 4 / 127

Contents 4

Installing a storage controller and FBWC module ........................................................................................ 40

Installing a Smart Storage Battery ................................................................................................................ 42

Drive cable options ................................................................................................................................................... 43

Mini-SAS cable options ................................................................................................................................. 43

Optical drive option ................................................................................................................................................... 45

Redundant fan option ............................................................................................................................................... 46

Fan population guidelines ............................................................................................................................. 47

Installing a hot-swap fan module................................................................................................................... 47

Memory options ........................................................................................................................................................ 49

Memory-processor compatibility information ................................................................................................ 49

SmartMemory ................................................................................................................................................ 50

Memory subsystem architecture ................................................................................................................... 51

Single-, dual-, and quad-rank DIMMs ........................................................................................................... 51

DIMM identification ........................................................................................................................................ 52

Memory configurations .................................................................................................................................. 52

General DIMM slot population guidelines ..................................................................................................... 53

Identifying the processor type ....................................................................................................................... 54

Installing a DIMM ........................................................................................................................................... 54

Processor option....................................................................................................................................................... 55

Processor installation cautions...................................................................................................................... 56

Installing a processor .................................................................................................................................... 56

FlexibleLOM option .................................................................................................................................................. 61

Full-height half-length riser option ............................................................................................................................ 63

Expansion board options .......................................................................................................................................... 65

M.2 SSD enablement option .................................................................................................................................... 68

Dual 8Gb microSD Enterprise Midline USB device ................................................................................................. 70

Redundant power supply option............................................................................................................................... 71

Power input module and RPS backplane characteristics ............................................................................. 71

Installing the redundant power supply option ............................................................................................... 71

HP Trusted Platform Module option ......................................................................................................................... 76

Installing the Trusted Platform Module board ............................................................................................... 76

Retaining the recovery key/password ........................................................................................................... 78

Enabling the Trusted Platform Module .......................................................................................................... 78

Cabling ...................................................................................................................................................... 80

Cabling overview ...................................................................................................................................................... 80

Storage cabling......................................................................................................................................................... 80

Four-bay LFF non-hot-plug drive cabling ...................................................................................................... 80

Four-bay LFF hot-plug drive cabling ............................................................................................................. 81

M.2 SSD cabling ............................................................................................................................................ 83

FBWC cabling........................................................................................................................................................... 85

Smart Storage battery cabling .................................................................................................................................. 87

Power supply cabling ............................................................................................................................................... 88

Optical drive cabling ................................................................................................................................................. 89

Front I/O cabling ....................................................................................................................................................... 89

Software and configuration utilities ........................................................................................................... 90

Server mode ............................................................................................................................................................. 90

Product QuickSpecs ................................................................................................................................................. 90

HPE iLO .................................................................................................................................................................... 90

Active Health System .................................................................................................................................... 91

RESTful API support for iLO ......................................................................................................................... 92

Integrated Management Log ......................................................................................................................... 92

Intelligent Provisioning ............................................................................................................................................. 92

HPE Insight Diagnostics ................................................................................................................................ 93

HPE Insight Diagnostics survey functionality ................................................................................................ 93

Erase Utility ................................................................................................................................................... 93

Scripting Toolkit for Windows and Linux .................................................................................................................. 94

Service Pack for ProLiant ......................................................................................................................................... 94

HP Smart Update Manager ........................................................................................................................... 94

HPE UEFI System Utilities ....................................................................................................................................... 94

Using UEFI System Utilities .......................................................................................................................... 95

Summary of Contents for ProLiant DL60 Gen9
































































































































Search results

Summary of Contents for ProLiant DL60 Gen9

Reviews:

Related manuals for ProLiant DL60 Gen9

Brands by name

Popular brands

HP ProLiant DL60 Gen9, User Manual

Search results

Summary of Contents for ProLiant DL60 Gen9

Reviews:

Related manuals for ProLiant DL60 Gen9

Brands by name

Popular brands